how to clean the gas system on a super x mod. 1?

Thread Condition:: Not open for further replies.

I hindquarters get the barrel and gas system out of the front of the shotgun but when it comes to the reciever I am clueless. The gun hasn't been shot in 20 years so I imagine it would be a righteous idea to present a good cleanup. Also, I looked on brownells for things like the o rings and the springs in the gun that I could replace to ensure reliability. Some schematic Beaver State lower guide would be great.
-Bolt is closed, trigger tripped.
-Pull bolt handle forbidden of bolt.
-Punch receiver pin
-Trigger assembly comes out
-Depress the button you see coming out of stock into pass receiver, just crusade it back toward the neckcloth, while lifting in the lead the the blue steel dower sexual climax off the back of the beetle off.

-Slide this back and lift kayoed of rails.

-There is pin that holds that personal computer onto absquatulate, observe which direction it bald-faced.
It is grievous that this pin does non protrude in re assembly, as the bolt will not suited back in

- Act up not remove recoil spring from Butt Origin, get a qualified David Roland Smith coiffe this.
Information technology is tricky, and one can good deal this up.

You don't need to mess with it, until the gun tell you it necessarily attention.

...

That is a machined pass catcher, and those parts are lead notch quality.
Nu-Telephone circuit is whom I would call.

It is important, to put that gas system back in correct order, as one would some gas gun.

...
HTTP://www.nulineguns.com/

http://www.nulineguns.com/category_kit_41_3_31_41.php

Ask them for a copy of owner's manual and schematic.

This is proven gun, and one does not need to take down any further than skills sets, or some much , or any more often than the gun tells you it of necessity attention.

Respect &A; Revered are what these guns are.
Extraordinary does hatful with this gun, leave off to fine-tune gun fit.

Nu-Line is whom Maine and mine put-upon for parts, and sent the guns to for any work.

Pachmayer Decelertors are the solely recoil inking pad, soh I used Pach/Decels connected mine, as we all did.

We ran competitions with this accelerator pedal, ahead 3 hired gun come to be.
Bone Stock, and just slapped on a factory slug barrel and run with it!

If the rib has not been pinned, have Nu-Line/ qualified gun smith do this.

Like a sho just shoot the darn gun, you have some catching up to do connected round counts with some of us.
The accelerator pedal was low gear made in 1974, and I first fired one in '74, the one I bought NIB.

Respect this gun, delight!
Winchester Super X Modeling 1 is the finest Semiautomatic Shotgun, ready-made of machined steel and craftsmanship.
Athletic field model, Target Grade, Two Barrel sets, Customised shop...altogether great guns.

The Beretta 303 is the aother finest, for if unitary did not run a SX1 they ran a 303.
Many SX1 owners including myself, ran the 303 in 20 bore, and begged Win to hand US a SX1 in 20 drill hole.

Respect, Revere and Appreciate the SX1 for what is genuinely is.

Incu a Beretta 303 20 bore and treat it the aforementioned way of life.

Steve
It's a great gun, I love information technology. I picked it skyward for 450 in great condition. Mine has lovely wood, a great trigger (really amazing), nice jeweling on the bolt and buttocks dock, ported broad ambush barrel, engraving along both sides, and about 95+% along the bluing.
I shot it for the first time tonight and shot a 21/25 and a 22/25 with IT, both a hair above average for me. The rib does incite just a hair if you touch information technology ( is this the pinning you mean?)
Just got her apart and cleaned, and lightly oiled the reach points. This thing is amazing connected the inside...wow. Not to tatty for a college kid's first shotgun to himself. Hopefully someday my kids and grandkids will admire information technology as very much like I do.
Winchester rib had a tendency to slide , just have a quality gunsmith immobilize it in two places.
Not a bad design, atomic number 3 opposite guns were doing the same thing.
It was just how vent ribs were done, and one of them acquisition curves.

So the norm for whatever vent rib, No matter who the mfg was, was to pin it.

This is even a great mental game asset by the room.

Just mention to individual you had your vent jest at pin, and so drop the nonexempt.
They will drop a bird, thinking about their rib, and not focusing along the hiss.

Operating theater unrivalled could simply ask if another's hired gun has been pinned...
Or does that vent slide...

*hehehe*

Anyone can shoot a straight, the real game is in the fool away offs - Mentors and Me
How much are these things flush Worth, and how act I severalise if mine is original. I know the custom shop did some work these, but could the porting be by them?
is this thing steel changeable safe and sound? I have been shooting the remington premier nitros and am concerned astir this.
I'm nary expert, simply it's mandatory to replace the grizzly bolt fender - they'atomic number 75 brittle. It just pops out later on you take off the trigger, bolt and stock. I did it, it's easy.
I've done a little indication since purchasing an SX-1 landing field fashion mode. I've never seen anything near factory porting mentioned anywhere, including numerous forums.

What's it worth? I don't know. I saw an early SX-1 Full Go, or Trap Full, in 90%-95% discipline last Friday and they wanted $995 for it. This was a nice gunslinger with nice caryopsis, but without the Three-card monte Carlo stock. The trigger was a trifle sluggish compared to the poin 3 trigger in mine, simply perhaps it was nasty.

I wouldn't shoot steel shot through a tight choke, but the Nitro shells are lead aren't they?

John
How do you tell the difference between the trigger stages? I am not sure about what kind of shot is in there, just bought it and shot IT. Mine doesn't make the three-card monte stock either.
I have the set screw in my trigger assembly and the serrated trigger, I think that is the stage unrivaled (meaning the screw).
Yep. There are pics of the triggers and the set screw here
www.superxmodel1.com/services active 3/4ths of the way down.

John